K8、JK8机翼接头与检验量规协调准确度的提高

分析了 K8、 JL8机翼接头孔精加加后与检验量规位置协调的条件，介绍了为提高它们之间协调准确度所采取的措施及其效果。     

航天主要金属结构材料与肼的相容性

概括地探讨了金属材料和肼相容性的基本原理和研究重点，叙述了６０年代以来国外金属材料和肼相容性研究的发展，较详细地介绍了了钛合金，不锈钢和铝合金在推进剂中相容性的研究成果并进行了总结归纳。     

Compression Creep Behavior of High Volume Fraction of SiC Particles Reinforced AI Composite Fabricated by Pressureless Infiltration

The compression creep deformation of the high volume fraction of SiC particles reinforced AI-Mg-Si composite fabricated by pressure-less infiltration was investigated. The experimental results show that the creep stress exponents are very high at temperatures of 673 K, 723 K and 773 K, and if taking the threshold stress into account, the true stress exponent of minimum creep strain rate is still approximately 5, although the volume fraction of reinforcements is very high. The creep strain rate in the high volume fraction reinforced aluminum alloy matrix composites is controlled by matrix lattice diffusion. It is found that the creep-strengthening effect of high volume fraction of silicon carbide particles is significant, although the particles do not form effective obstacles to dislocation motion.     

The double-pulsar binary J0737–3039

A recent multibeam pulsar survey of the outer Galactic plane at Parkes has discovered the first-known double-pulsar binary, a very compact double neutron star system in which both stars are observable as radio pulsars. In this review, we briefly describe the discovery and the studies which have been enabled by the unique properties of the system. These range from the most precise confirmation yet of the theory of general relativity, with the possibility of even more new tests and the measurement of second-order post-Newtonian effects, to studies of the magnetospheres and emission properties of the two pulsars. The discovery also results in a significant increase in the expected rate of occurrence of the mergers of double neutron star systems, and hence the rate of detection of such events by the new ground-based gravitational wave detectors.     

离心铸造Al—20wt%Si合金自生表面复合材料的组织与性能

采用热模金属型离心铸造Al－20wt％Si合金，获得了外层聚集粗大初晶Si、中层为共晶组织、内层聚集细小初晶Si的自生三层表面复合材料。考察了复合材料的组织形貌，检测了复合材料的硬度和耐性，分析了复合材料的断裂模式。     

TC11钛合金的热态变形行为研究

采用等温恒应变速率压缩试验法,研究了TC11合金在780℃-1080℃和应变速率为0.001s-1~70s-1范围内的高温压缩变形行为。考察了变形温度、应变速率及变形程度对流动应力的影响关系。结果表明,流动应力对变形温度和应变速率敏感,随变形温度升高和应变速率降低流动应力减小,特别是在α β两相区变形温度对流动应力的影响显著。     

阳极氧化铝模板法制备CoPt纳米管

采用电化学直流沉积,首次在氧化铝模板中成功制备出直径为50 nm的CoPt纳米管高度有序阵列。利用透射电子显微镜(TEM)、扫描电子显微镜(SEM)、X射线衍射仪(XRD)以及振动样品磁强计(VSM)对样品的结构和磁学特性进行测试。分析表明,CoPt纳米管是以面心立方(fcc)结构存在。当外加磁场与纳米线平行时,CoPt合金纳米管的矫顽力达450 Oe,这种大面积制备的CoPt纳米管希望在超高密度信息磁存储上得到应用。     

铝合金冷挤压工艺的优化

本文介绍了6A02、6063铝合金冷挤压试验过程。通过专门装置测试铝合金冷挤压中不同凹模表面粗糙度、挤压速度、润滑剂、坯料状态的下的挤压力,利用正交试验L9(34)得出最优工艺参数。结果表明冷挤压过程中模具表面并非越光越有利于成形,坯料也要针对不同的挤压材料应选用不同的热处理方法。本实验为铝合金冷挤压提供了可行的实验方法和生产依据。     

改进剥层应变法测量铝合金预拉伸厚板内部残余应力分布

铝合金预拉伸板已广泛应用于航空整体结构件的制造,其内部初始残余应力引起的加工变形已严重制约新型飞机的研制和生产。测量残余应力的方法很多,但一般只能测量工件的表面和浅表层,而厚板内部残余应力测量一直是工程中的难点。文中针对铝合金预拉伸厚板的特点,提出了测量其内部残余应力的方法,并运用弹性力学理论进行了理论推导,得到了应力-应变关系矩阵。用该方法测量了7050T7451铝合金厚板内部残余应力,并对测试结果进了分析和比较。结果表明,本文提出的方法有效地解决了厚板内部残余应力测量的难题,有较高的工程应用价值。